Compósitos de resina Poliuretana (PU) derivada de óleo de mamona e partículas de bambu (Dendrocalamus giganteus) foram preparados com 10, 15 e 20% em peso de PU pelo processo de prensagem. O objetivo do presente estudo foi criar uma solução para aproveitar resíduos da manufatura do bambu, minimizando impactos negativos ao meio ambiente, adicionando-lhe uma resina que não contém compostos orgânicos voláteis (COV). A sua caracterização foi feita através de análises físicas e termogravimetria. A associação de PU com partículas de bambu produziu efeitos esperados como a diminuição no teor de umidade, inchamento e absorção de água com o aumento do percentual de PU. Nos ensaios de dureza Shore D obteve-se um aumento gradual da rigidez superficial com o acréscimo em percentual de resina PU.

Composites of Polyurethane (PU) resin derived from castor oil and bamboo particles (Dendrocalamus giganteus) were prepared by pressing with 10, 15 and 20% weight of PU. The aim of this study was to develop a new application of wastes from bamboo manufacture, minimizing the negative impact to the environment, adding a resin free of volatile organic compounds (COV). The composite characterization was performed with physical and thermogravimetric analysis. The association of PU and bamboo particles produced the expected effects, including a decrease in moisture content, swelling and water absorption as PU percentage increased. The Shore D hardness increased with the percentage of resin PU in the composite.

Gamma and ultraviolet radiation effects on hardness, elastic modulus and viscoelastic properties of polyurethane derived from castor oil (PU) were investigated by nanoindentation tests. Modifications on surface morphology, induced by radiation, were observed by atomic force microscopy. The polyurethane derivate from castor oil shows good resistance to gamma radiation, with only small changes in hardness, elastic modulus, viscoelastic properties and contact angle. The hardness of PU increases at the near surface region due to UVA radiation and decreases after UVC radiation. The contact angle for water drop decreases after UVC radiation, but not after gamma radiation, despite a significant increase in roughness. Such results are attributed to different responses from polyurethane to radiation energy. Increase in hardness due to UVA is attributed to a higher crosslinking at shallow depths, while a decrease in mechanical properties may be attributed to chain scission. These results are consistent with the modifications on viscoelastic properties. Shore D hardness did not show the same trend as observed by nanoindentation results. Hardness, viscoelastic properties and contact angle of castor oil polyurethane are more severely influenced by UVC radiation, while gamma radiation does not have a significant effect.

Neste trabalho são investigadas as propriedades mecânicas de poliuretana derivada do óleo de mamona, utilizando a técnica de indentação instrumentada com penetradores de geometrias piramidal e esférica. Foi analisada a influência da forma do penetrador utilizado nos ensaios de indentação instrumentada para se obter valores das propriedades mecânicas de polímero derivado de óleo de mamona. Os penetradores utilizados são de pontas piramidais dos tipos Berkovich e canto de cubo e esférico de raio igual a 150 μm em um Nanoindenter XP TM com cargas aplicadas entre 1 e 200 mN. As penetrações variam de acordo com o formato do penetrador, sendo maiores para pontas agudas. A dureza e o módulo de elasticidade foram determinados, utilizando o método de Oliver e Pharr. Verificou-se que os valores medidos para a dureza são maiores para penetradores mais agudos. Os valores obtidos com a ponta piramidal Berkovich foram de 0,14 GPa para pequenas penetrações e 0,12 GPa para maiores penetrações. Já os valores obtidos com ponta canto de cubo foram 25 a 30% maiores. Isso está relacionado com os volumes das regiões que apresentam deformações plásticas elevadas, no caso de penetradores agudos comparados com os volumes das regiões que sofrem deformações viscoelásticas. A viscosidade aparente determinada, utilizando penetrador esférico em testes de força aplicada constante, é igual a (22 ± 2) × 10(12) Pa.s.

The mechanical properties of polyurethane derived from castor oil, obtained by instrumented indentation technique with pyramidal and spherical indenters are reported. The influence of the indenter shape on the values of mechanical properties of the polymer was investigated. The indentations were made with pyramidal Berkovich, cube corner and a spherical indenter with radius of 150 μm in a Nanoindenter XP TM. The applied loads varied between 1 and 200 mN. The penetration depth increases for acute indenters, being higher for the cube corner tip. The hardness and elastic modulus were determined using the method of Oliver and Pharr. It was found that the measured values for hardness are higher for more acute indenters. The hardness with the pyramidal Berkovich tip was 0.14 GPa for small penetrations and 0.12 GPa for higher penetration depths. The values obtained with a cube corner tip were 25 to 30% higher. This is related to the volumes of regions with high plastic deformation in the case of acute indenters compared to the volumes of regions that present viscoelastic deformation. The apparent viscosity determined using the spherical indenter, in tests with applied constant forces, is equal to (22 ± 2) × 10(12) Pa.s.